GRIDLINE

← All guides

Projects

The builder

Draw a floor’s plan: walls, windows, doors, floor areas and stairs; set the scale; undo, duplicate and use keyboard shortcuts. Changes save on their own.

Open a project and press the Builder tab. It shows one floor’s plan; pick another floor with the Floor list at the top (the address keeps the floor, so you can bookmark it). A new plan is an empty grid where 1 px is 1 cm, with lines every 10 cm and every metre.

Draw

  • Wall: drag from one end to the other. Walls snap to horizontal or vertical and to the ends of other walls; hold Alt for any angle. The tool stays on, so you can draw the next wall right away.
  • Window and Door: click on a wall. A door on an exterior wall starts as an outdoor door; change the type in the side panel.
  • Floor: drag a rectangle over a floor area (a room, a terrace, a ramp). The areas of all floor areas add up.
  • Floor shape: click each corner of a floor of any shape. Click the first corner, double-click or press Enter to close it; Esc cancels.
  • Stairs: drag a rectangle over the stairs. They rise along the longer side.
  • Set scale: drag along a distance you know, then type its real length and press Set scale. Every length and area follows the new scale.

Select, move and resize

  • With Select, click an item to select it and drag it to move it. Drag empty space to move the view; use the mouse wheel or Zoom in, Zoom out and Fit the plan to zoom.
  • Drag the handles of the selected item: a wall’s round ends, the square ends of a window or door (its width), the corners of a floor or stairs.
  • On a free-shape floor, drag a corner to move it, drag a small round handle on an edge to add a corner, and Alt+click a corner to remove it.
  • On a phone the builder shows the plan and lets you select items; drawing works best on a larger screen.

The side panel

The panel next to the plan shows the selected item. Empty fields use the default shown in grey: the floor’s value, else the project’s Standard values, else the catalog. Type a value to set it for this item only; clear the field to use the default again.

  • Wall: Length (empty = the length measured on the plan), Height, Thickness, Exterior wall and Material. Type a wall’s real length and press Use as scale reference to set the scale of the whole plan from it.
  • Window or Door: Type (a window, or an indoor, outdoor or garage door), Width, Height, Height from floor (windows) and Catalog item.
  • Floor area: Width and Depth, or Change to free shape; tick Inclined floor (ramp, slope) to set Rises towards and Height difference. The panel shows the slope and the real (sloped) area.
  • Stairs: Shape (one flight, or two flights with a landing), Type, Height to climb (floor to floor), the steps of each flight and the landing height. It shows the riser and tread, and a warning when 2 × riser + tread is outside the comfortable 60–65 cm. Flip direction and Swap sides turn the stairs.

The strip under the plan shows this floor’s Wall length, Net wall area, Floor area, Windows and doors and Estimated cost, updated as you draw.

Undo, duplicate, delete

The toolbar has Undo and Redo (the last 100 steps of each floor’s plan; a drag counts as one step), Duplicate and Delete. A duplicated wall appears 1 m to the side with its windows and doors; a floor area or stairs 0.5 m away; a window or door next to the original on the same wall. Deleting a wall also deletes its windows and doors. The undo history is kept while you switch floors and lost when the page reloads.

Keyboard shortcuts

  • Delete or Backspace: delete the selected item.
  • Ctrl+Z: undo. Ctrl+Y or Ctrl+Shift+Z: redo.
  • Ctrl+D: duplicate the selected item.
  • Enter: close the free-shape floor being drawn. Esc: cancel drawing and go back to Select.
  • Alt: any angle while drawing; Alt+click a corner to remove it.
  • On a Mac, use Cmd instead of Ctrl. Shortcuts do nothing while you type in a field. The Keyboard shortcuts button lists them too.

Saving

The plan saves on its own a moment after you stop drawing. The line at the top shows Unsaved changes, Saving…, then All changes saved. While changes are not saved, the browser asks before you leave the page. If it shows Not saved, the reason is next to it (for example a plan too large to save); your drawing stays on the page and the next change tries again.

If the same plan is open in two tabs or windows and both change it, the older one shows Changed in another tab or window: press Reload to see the latest version, or Overwrite to save your plan over it. If the floor is removed in another tab, the builder shows This floor was removed and stops saving; Go to the Overview takes you back.

Floors that share a plan

When several floors use the same plan (Same plan as on the Overview), the builder says so above the toolbar: Edits change floors: lists every floor that changes with your edits, and Stairs counted on: lists the floors whose quantities include the plan’s stairs. See Floors and shared plans.